- Main Catalog
- Batteries And Electronics
- Batteries
- Fantom Battery Pack 3300mAh
Factory Race Pack 6 cell
- Fukuyama Racing Batteries Pack 1.160V~1.169V
Match Pack Cells from Fukuyama Racing
- Intellect 3800mAH sub C size batteries
- Pansan Pure Energy
Ni-MH batteries, 3600 mAh, Sub-C size
- VXR Racing 1/10th 2S1P 3600mAh Li-Po Power Pack
Capacity: 3600mAh
Weight: 175 grams
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 20C
Dimension(mm): 15 x 44 x 128
Recommended Application: 1/10th EP
- VXR Racing 1050mAh Li-Po Micro Power Pack
Capacity: 1050mAh
Weight: 79 grams (including wire and connector)
Li-Po cell arrangement: 3S1P
Norminal voltage:11.1 Volts
Discharge capability: 10C
Dimension(mm): 62 x 35 x 17
Wire: 13 G Silicon
Connector: Open ended
Recommended Application: 1/18th EP
- VXR Racing 1300mAh Li-Po Micro Power Pack
Capacity: 1300mAh
Weight: 90 grams (including wire and connector)
Li-Po cell arrangement: 3S1P
Norminal voltage:11.1 Volts
Discharge capability: 10C
Dimension(mm): 80 x 28 x 18
Wire: 16 G Silicon
Connector: Open ended
Recommended Application: 1/18th EP
- VXR Racing 1300mAh Li-Po Micro Power Pack
Capacity: 1300mAh
Weight: 60 grams (including wire and connector)
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 80 x 27 x 12
Wire: 13 G Silicon
Connector: Open ended
Recommended Application: 1/18th EP
- VXR Racing 2100mAh Li-Po Micro Power Pack
Capacity: 2100mAh
Weight: 104 grams (including wire and connector)
Li-Po cell arrangement: 2S2P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 62 x 35 x 24
Wire: 13 G Silicon
Connector: Open ended
Recommended Application: 1/18th EP
- VXR Racing 2600mAh Li-Po Micro Power Pack
Capacity: 2600mAh
Weight: 119 grams (including wire and connector)
Li-Po cell arrangement: 2S2P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 84 x 25 x 24
Wire: 13 G Silicon
Connector: Open ended
Recommended Application: 1/18th EP
- VXR Racing Enduro Series Li-Po Transmitter Pack for KO Helios and JR Z1
Capacity: 1300mAh
Transmitter Run time: 5 to 6 hours
Weight: 87 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 83 x 28 x 20
Connector: ‘J'' Type
- VXR Racing Enduro Series Li-Po Transmitter pack for Sanwa M11 and Futaba 3P series
Capacity: 1700mAh
Transmitter Run time: 7 to 8 hours
Weight: 113 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 90 x 51 x 12
Connector: ¡®J'' Type
- VXR Racing Enduro V2 Li-Po Transmitter Pack for Futaba 3P Series
Capacity: 3300mAh
Transmitter Run time: 14 to 16 hours
Weight: 185 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 115 x 60 x 14
Connector: ‘J'' Type
- VXR Racing Enduro V2 Li-Po Transmitter Pack for KO Helios and JR Z1
Capacity: 2300mAh
Transmitter Run time: 10 to 12 hours
Weight: 133 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 105 x 35 x 21
Connector: ‘J'' Type
- VXR Racing Li-Po Batteries 1050mAh
FLIGHT PACK, LI-PO, 1050MAH, 10C, 14.8V,4S1P.
- VXR Racing Li-Po Batteries Pack 1050mAh
FLIGHT PACK, LI-PO, 1050MAH, 10C, 7.4V, 2S1P.
- VXR Racing Li-Po Batteries Pack 1050mAh
FLIGHT PACK, LI-PO, 1050MAH, 10C, 11.1V, 3S1P.
- VXR Racing Li-Po Batteries Pack 2000mAh
FLIGHT PACK, LI-PO, 2000MAH, 12C, 7.4V, 2S1P
- VXR Racing Li-Po Batteries Pack 2000mAh
FLIGHT PACK, LI-PO, 2000MAH, 12C, 11.1V, 3S1P
- VXR Racing Li-Po Batteries Pack 2100mAh
Flight Pack Li-Po 2100mAh, 6C 11.1V, 3S2P
- VXR Racing Li-Po Batteries Pack 3150mAh
FLIGHT PACK, LI-PO, 3150MAH, 6C, 7.4V, 2S2P
- VXR Racing Li-Po Batteries Pack 3150mAh
FLIGHT PACK, LI-PO, 3150MAH, 6C, 11.1V, 3S3P.
- VXR Racing Li-Po Battery Pack For Sanwa M8 3S1P,11.1V,1100mAh
Capacity: 1100mAh
Transmitter Run time: 4 to 5 hours
Weight: 105 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 172 x 47 x 17
- VXR Racing Li-Po Transmitter Pack for Sanwa M11 and Futaba 3PK Series
Capacity: 2300mAh
Transmitter Run time: 10 to 12hours
Weight: 146 grams
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 100 x 50 x 14
- VXR Racing Micro Power Pack 1050mAh for 1/18 scale
Capacity: 1050mAh
Weight: 52 grams (including wire and connector)
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 62 x 35 x 12
Recommended Application: 1/18th EP
- VXR Racing Miscellanous
- VXR Racing Receiver Pack 1000 mAh
Capacity: 1000 mAh
Weight: 52 grams (including wire and connector)
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 6C
Dimension(mm): 34 x 12 x 52
Connector: JST - RCY Polarized
Recommended Application: 1/10th GP & 1/8th GP
Note: Unit must be used with 5A VXR Voltage Regulator
- VXR Racing Receiver Pack 120mAh
120mAh, 2S1P, 7.4Volts, 10C
Model Number: LRX-0120
Weight: 7 grams|
Dimension(mm): 31 x 16 x 8.5
Recommended Application: 1/12th EP
Connector: JST – RCY Polarized
Note: Must be used with VXR LDO Voltage Regulator LVR-1000 or LVR-5000
- VXR Racing Receiver Pack 1300mAh
Capacity: 1300mAh
Weight: 61 grams (including wire and connector)
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 83 x 28 x 13
Connector: JST - RCY Polarized
Recommended Application: 1/10th GP & 1/8th GP
- VXR Racing Receiver Pack 2000mAh
Capacity: 2000 mAh
Weight: 93 grams (including wire and connector)
Li-Po cell arrangement: 2S2P
Norminal voltage: 7.4 Volts
Discharge capability: 6C
Dimension(mm): 34 x 24 x 52
Connector: JST - RCY Polarized
Recommended Application: 1/10th GP & 1/8th GP
Note: Unit must be used with 5A VXR Voltage Regulator
- VXR Racing Receiver Pack 240mAh
240mAh, 2S2P, 7.4Volts, 10C
Model Number: LRX-0240
Weight: 14 grams
Dimension(mm): 31 x 16 x 16
Recommended Application: 1/10th EP
Connector: JST – RCY Polarized
Note: Must be used with VXR LDO Voltage Regulator LVR-1000 or LVR-5000
- VXR Racing Receiver Pack 500mAh
500mAh, 2S1P, 7.4Volts, 10C
Model Number: LRX-0500
Weight: 23 grams
Dimension(mm): 42 x 25 x 12
Recommended Application: 1/10th GP
Connector: JST – RCY Polarized
Note: Must be used with VXR LDO Voltage Regulator LVR-1000 or LVR-5000
- VXR Racing Receiver Pack 750mAh
Capacity: 750mAh
Weight: 33 grams (including wire and connector)
Li-Po cell arrangement: 2S1P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 50 x 30 x 12
- VXR Racing Receiver Packs - Li-Po, 2600 mAh, 2S2P, 7.4V
Capacity: 2600mAh
Weight: 116 grams (including wire and connector)
Li-Po cell arrangement: 2S2P
Norminal voltage: 7.4 Volts
Discharge capability: 10C
Dimension(mm): 83 x 28 x 26
Connector: JST - RCY Polarized
Recommended Application: 1/8th GP off-road
- VXR Racing Supalite Series Li-Po Transmitter Pack for KO Series and JR Z1
Capacity: 500mAh
Transmitter Run time: 2 hours
Weight: 38 grams
(versus 225gm - 8 AA GP1800 Ni-MH with KO battery holder)
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 85.5 x 26 x 12.5
Connector: ‘J'' Type
- VXR Racing Supalite Series Li-Po Transmitter Pack for Sanwa M11 and Futaba 3P Series
Capacity: 500mAh
Transmitter Run time: 2 hours
Weight: 37 grams
(versus 227gm - 8 AA GP1800 Ni-MH with Futaba battery holder)
Li-Po cell arrangement: 3S1P
Norminal voltage: 11.1Volts
Discharge capability: 10C
Dimension(mm): 78 x 44 x 8
Connector: ‘J'' Type
- VXR Racing Transmitter Pack for KO Propo Mars Series. KO Helios, & JR Z1
750mAh, 3S1P, 11.1Volts, 10C
Model Number: LTK-0001
Weight: 58 grams
Dimension(mm): 100 x 31 x 14
Connector: ‘J'' Type
- VXR Racing Transmitter Pack for Sanwa M11and Futaba 3P Series
(3 to 4 hr run time, 3S1P, 11.1Volts, 76 grams , 106 x 54 x 10 mm, ‘J'' Type Connector)
- VXR Racing Transmitter Pack for Sanwa/Airtronics M8 & Stylus
800mAh, 3S1P, 11.1Volts, 10C
Model Number: LTS -0001
Weight: 86 grams
Size: 17 X 47 X 172
Voltage: 11.1v Nominal
Operating Time: 3 to 4 hours
- Chargers
- Bantam E-Station BC5
- LRP Micro charger
- LRP NiMH Digital Charger
Digital Charger
- LRP Pulsar Competition Charger
PROFESSIONAL BATTERY AND MOTOR MANAGEMENT
- LRP Pulsar Sport Charger
PROFESSIONAL BATTERY MANAGEMENT
- Prolux Digipeak Charger
DC 1-14cell Peak Predict Charger
- VXR Racing Apache Smart Charger 2030
Capable of charging: 1 - 3 cells Li-Po, 1 - 8 cells Ni-CD / Ni-Mh
Input voltage: DC 11 to 15 Volts
Current Selection(mAh): 110, 250, 500, 750, 1200 mAh
Output Connector: JST - RCY Polarized
Input Connector: Crocodile clips
- VXR Racing Apache Smart Charger 2500
LI-PO SMART CHARGER 1-4 CELL
Capable of charging: 1 - 4 cells Li-Po
Input voltage: 10.5 - 15VDC
Current Selection(mAh): 250mAh to 2500mAh
Output Connector: JST Female
Input Connector: Aligator Clip
This charger is only for Li-Po battery. Cannot charge Ni-Mh or Ni-Cd.
- VXR Racing Apache Smart Charger SM-2700Li
Capable of charging: 1-5 cells Li-Po only
Input Power source: 11V-15V DC requires 5A current rate at maximum charge rate.
Charge Voltage : 3.7V-7.4V-11.1V-14.8V-18.5V
(1- 5 cells in series )
Charge Current : 500mA-1000-1500-2000-3000-3500mA
Full charge voltage : 4.2V per cell
Overcharge auto cut off voltage : 4.28V/Cell
Maximum output power : 45Watt
(Note: Max 2.5A for 4S & 2A for 5S)
Size : 1.62" x 4" x 0.62" (42mm x 102mm x 16.2mm)
- Radio
- Radios
- Airtronics Blazer Sport
The BLAZER Sport is your best choice for start racing of any kind. Built with the same digital technology as out top of the line M11, you will definitely have total control. Feel the smoothness of the steering wheel or trigger and you will know it is well designed.
- E-Sky 2CH Radio System
- E-Sky Simulator (USB Plug)
- Futaba 3PK Super
3PK Super — Now fully synthesized!
It''s been THE system of choice for drivers of all skill levels; now Futaba takes 3PK technology to new heights with two versions that add even more features and convenience!
- Futaba 3PS FASST
- RC Aircraft & Accessories
- Heli
- Heli RTF
- E-Sky Heli Kit Honey Bee
This kit includes Heli kit, Transmitter unit, Charger, 2 Li-Po, 2S1P, 7.4V, 1000mAh.
- E-Sky Lama II Indoor Heli
This Heli included with Li-Po Battery 7.4V, Transmitter Set, Charger, Power Supply out put 12V and is totally ready to fly.
- E-Sky Lama V3 Indoor Heli
This Heli included with Li-Po Battery 7.4V, Transmitter Set, Charger, Power Supply out put 12V and is totally ready to fly.
- E-Sky Lama V4 Indoor Heli
(1) Main rotor diameter:340mm
(2) Weight:230g
(3) Length:408mm,width:85mm,height:180mm
(4) Power system:180 motor*2
(5) KIT/ARF/RTF:RTF
(6) Transmitter:Standard 4 CH
(7) Mix controller:4 in 1 controller(W/gyro,mixer,ESC,receiver)
(8) Servo:8g,1.3kg.CM,0.12s/60°
(9) Battery:7.4V 800mAh Li-polymer battery
- E-Sky RTF Robins 22 Heli
- WALKERA R/C HELICOPTER
This kit includes Heli kit, Transmitter unit, Charger, Ni-Mh battery, 650mAh, 10.8V.
- RC Vehicle & Accessories
- Car Kit
- 1/10 EP Touring
- Alex Racing Design Stinger Kit (Blue)
- Tamiya Calsonic Impul Z TB-02
Overall length: 440mm
Overall width: 189mm
Overall height: 119mm
Weight Fully-Equipped: 1,564g
Wheelbase: 259mm
Type RS-540 motor included
Transmission Type: Longitudinally mounted motor with shaft-driven 4WD
Diff. gear system: Ball Diff (Front & Rear)
Steering Tie Rod: 3 part
Suspension: Double Wishbone (F&R)
Damper: C.V.A. Super Mini Shock Unit (F&R)
Gear Ratio: 7.94:1
Tire Width: 24mm (F&R)
Tire Diameter: 64mm (F&R)
Tread Pattern: Racing Slick (F&R)
Speed Controller: Electronic Speed Controller (not included)
- Tamiya Esso Ultraflo Supra (TA05 Chassis)
Length: 442mm
Full ball bearing configuration for maximum efficiency
Single-deck frame and other features make performing maintenance easier than ever
Chassis structure designed for ultra-low center of gravity and optimum balance
- Tamiya Rising Storm
Total length: 395mm
Total width: 249mm
Total height: 150mm
Chassis Material: ABS
Suspension: Double wishbone 4-independent wheel (front and rear)
Drive train: Shaft-driven 4WD
Equipped with a Type 540 motor
Tire Diameter: 86mm (front & rear)
- Tamiya Subaru Impreza WRC Monte Carlo ''05 (Drift Spec)
Overall length: 441mm, Overall width: 185mm, Overall height: 145mm
Wheelbase: 257mm
Motor: Type RS540
Transmission: Shaft driven 4WD with longitudinally mounted motor
Diff gear: F/R 3 bevel diff
Steering tie-rod: 3-part
Suspension: F/R double wishbone
Damper: F/R friction dampers
- Tamiya TT-01R Chassis Kit
Overall length: 380mm
New design bumper and suspension arm
Steel drive shaft and axle
Racing performance spur gear set
Powered by GT-Tuned motor
CVA oil dampers
Full ball bearings
Carry case design packaging
- Tamiya XB Citroen Xsara WRC (Factory Assembled)
Overall length: 423mm
Overall width: 185mm
Overall height: 132mm
Wheelbase: 257mm
Type 540 motor included
Transmission Type: Longitudinally mounted motor with shaft-drive 4WD Chassis frame material: ABS
Suspension: Double Wishbone (Front & Rear)
- Tamiya XB Gravel Hound (Factory Assembled)
Total length: 400mm
Total width: 249mm
Total height: 170mm
Chassis Material: ABS
Suspension: Front and Rear Double Wishbone 4-independent wheel
Drive train: Shaft-driven 4WD
Equipped with a Type 540 motor
Tire Diameter F/R: Both 86mm
- Tamiya XB Mercedes-Benz C-Class DTM 2004 (Factory Assembled)
Overall length: 459mm, Width: 131mm, Height: 190mm
Transmission type: Longitudinally mounted motor with shaft-driven 4WD
Suspension: 4-wheel independent double-wishbone, Damper: friction type
Speed Controller: TEU-101BK electronic speed controller
Motor: High performance 540 type
Body: Polycarbonate body shell fully painted and pre-marked
Replaceable crystals allowing racing between friends.
- Tamiya XB Mini Cooper
Overall length: 332mm, Width: 166mm, Height:135mm
Chassis: Fully assembled M-03, Drive Train: 2WD front wheel drive
Suspension: 4-wheel independent double-wishbone, Damper: friction type
Speed Controller: TEU-101BK electronic speed controller
Motor: High performance 540 type
Body: Polycarbonate body shell fully painted and pre-marked
Replaceable crystals allowing racing between friends.
- Tamiya XB Wild Willy 2 (Factory Assembled)
Overall length: 325mm, Overall width: 272mm
Chassis type: Monocoque
Suspension: F/R double wishbone
Transmission type: Rear 2WD
Includes type 540 motor
Tire diameter: 115mm (F/R)
- Tamiya XB Zanavi Nismo Z (Factory Assembled)
Overall length: 440mm
Overall width: 189mm
Overall height: 122mm
Weight Fully-Equipped: 1,490g
Wheelbase: 257mm
Type 540 motor included
Transmission Type: Longitudinally mounted motor with shaft-drive 4WD Chassis frame material: ABS
Suspension: Double Wishbone (Front & Rear)
Tire Width: 27mm (F&R)
Tire Diameter: 65mm (F&R)
- Xray T2 1/10 Luxury Touring Car
- Xray T2''007 1/10 Luxury Touring Car
- Xray T2R 1/10 Premium Touring Car
- 1/10 GP Touring
- Serpent 710 4WD
The most anticipated car in Serpents history
- Serpent 720 1/10th scale 200mm
Serpent is pleased to announce their all-new 200mm race chassis, the Serpent 720. Based on the ultra successful Serpent 710, the car has been extensively tested on many different track conditions to ensure the best overall performance.
- XRay NT1 1/10th Luxury Nitro TC
Developed, designed and styled by legendary, award-winning Dipl. Eng. Juraj Hudy, the XRAY NT1 is exclusively manufactured by XRAY in Europe in the world’s most sophisticated RC manufacturing facility. The pure racing design and premium luxury quality with highest performance create the most sophisticated nitro touring car. Backed by XRAY’s legendary service and support, and showcased at racetracks worldwide by the winning XRAY Factory Team, the XRAY NT1 is taking the nitro touring world by storm.
- 1/18 Scale
- XRay M18MT - 4wd Shaft Drive 1/18 Micro Monster Truck Kit with Power Pack Pro
The XRAY M18MT is a lightweight high performance 4x4 micro monster truck capable of handling all that you can find for it. ...Race it. Jump it. Climb it. Crush it. With the one and only M18MT. From XRAY... Of course.
- XRay M18-RTR - 4WD Shaft Drive 1/18 Micro Car - Luxury RTR
- XRay M18T 4WD Shaft Drive 1/18 Micro Truck + Power Pack
XRAY M18T Professional 1/18 4WD shaft-driven micro truck
• optional conversion set transforms the truck into a monster truck
• maximum efficiency drivetrain includes 22 high-speed ball-bearings
• fully independent front and rear suspension
• oil-filled coil-over shocks
• servo saver included
• adjustable turnbuckles
• front and rear adjustable ball differentials
• adjustable shock position for damping adjustment
• easily-adjustable motor mount
• chassis accommodates 5 or 6 cell battery packs
• extensive line of micro electronics and optional parts from Xray
- XRay NT18 + Electronic Pack + Hudy Micro Starter Box
XRAY NT18 Professional 1/18 4WD shaft-driven micro nitro touring car
• the world''s first 1/18 nitro touring car
• 4WD shaft-drive micro nitro car
• powerful 0.8cc nitro engine
• super fast - speed more than 50km/hour (30mph)
• easy to drive and handle
• excellent fun and RC enjoyment
• works with any standard RC fuel
- XRay NT18MT 4WD 1/18 Micro Nitro Truck + Hudy Starter Box
Introducing XRAY''s NT18MT RTR kit… XRAY quality, built in the box!
XRAY’s nitro micro monster truck - the NT18MT - now comes fully assembled with an XRAY premium radio system and electronics set, creating a world-class RTR set. Assembled in the European XRAY factory, the ready-to-run micro nitro monster truck is ready to hit the track or your backyard!
- XRAY NT18T 4WD Micro Nitro Truck RTR + Hudy Starter Box
Introducing XRAY''s NT18T RTR kit… XRAY quality, built in the box!
XRAY’s nitro micro truck - the NT18T - now comes fully assembled with an XRAY premium radio system and electronics set, creating a world-class RTR set. Assembled in the European XRAY factory, the ready-to-run micro nitro truck is ready to hit the track or your backyard!
- 1/8 Off-Road
- GS Racing Storm RTR Plus
now available at RC Planet
Ready To Run Kit include:-
1)GS Fuel Bottle
2)GS Glow Starter
3)Pre-painted body shell
4)Transmitter, Receiver and 2 servo
- XRay XB8 EC
"To win a club race or a European Championship you need a car you can trust and rely on in any racing condition. With high praise and numerous awards across the world, the XB8 has proved its winning heritage...the spirit of racing...the pedigree of a true champion. "
TQ and Winner of the 2006 European Championship
XB8 – the champions’ choice --- your choice
Dipl. Eng. Juraj Hudy, Chief Designer
- XRay XB8R
The XRAY XB8R is a modern, high-competition, premium-quality 1/8 nitro off-road buggy based on the very successful and award-winning XB8 platform that was designed, developed, and styled by Dipl. Eng. Hudy Juraj. The XB8R, as with all other XRAY products, is exclusively manufactured by XRAY in Slovakia (Europe).
- Engines & Tune Pipes
- Exhaust Pipes
- Novarossi Tuned Pipe
Tuned Pipe With Ring And In-Satin Finish.
1/10th EFRA 2630.
- RD Logics "2 in 1" (Top & Bottom) One piece rear exhaust pipe set for .12 Turbo/Modified Engine (Outlaw)
- RD Logics .12 ONE PIECE PIPE SET W/REINFORCED STINGER(OUTLAW)
Anodized
- RD Logics One Piece Exhaust Pipe Set For 0.15 Engine
- RD Logics One piece pipe set for FW-05
Reinforced Stinger(outlaw)
- RD Logics One piece rear exhaust "Turbo II" pipe set for 1/8 Off Road
- RD Logics one piece rear exhaust pipe set w/ Reinforced Stinger (Outlaw)
- RD Logics One piece rear exhaust Turbo pipe set for NTC3
- RD Logics Turbo II One piece rear exhaust pipe set for FW05R
(outlaw)
- RD Logics Two piece rear exhaust pipe set for .12 engine (Outlaw)
- Vantage Racing 1/10 TC Carbon Fiber Pipe For V-One, RRR, 710, R40, MTX3 (.12-.15 Engine)
1/10 pipe for .12 - .15 engines
Fits: V-One RRR, 710, R40 and MTX3
- Vantage Racing 1/10 TC Carbon Fiber Tuned Pipe For V-One, RRR, 710, R40, MTX3 (.18 Engine)
1/10 pipe for .18-.21 engines
Fits: V-One RRR, 710, R40, MTX3
- Vantage Racing 1/8 Buggy/Truggy Carbon Fiber Tuned Pipe .23-.28 Engine (High Torque)
1/8 pipe for .23-.28 engines
Fits: Buggy/Truggy (High Torque)
- Vantage Racing 1/8 Off-Road Carbon Fiber Tuned Pipe (High Torque)
For .21 engine (High Torque)
Fits: Buggy
- VXR "Fire R" 1/8 Buggy In-Line Tuned Pipe Set (RPM)
Complete set of inline off road buggy high performance tuned pipes will provide you with high RPM performance.
- VXR "Fire T" 1/8 Buggy In-Line Tuned Pipe Set (Torque)
Complete set of inline off road buggy high performance tuned pipes will provide you with high torque performance.
- VXR Racing "Burst" Tuned Pipe Set for REVO
Turn your REVO into a high performance RC truck with just a simple upgrade! The Burst has it all!
- VXR Racing "Rage" Tuned Pipe Set for SAVAGE
Turn your SAVAGE intoa a powerful and unstopable machine with this high performance tuned pipe! Rage your SAVAGE!
- VXR Racing "X1" 1/10 In-Line Tuned Pipe Set - 5mm
Complete set of inline 5mm 1/10th high performance tuned pipes will provide you with all the power you will need!
- VXR Racing "X1" 1/10 In-Line Tuned Pipe Set - 6mm
Complete set of inline 5mm 1/10th high performance tuned pipes will provide you with all the power you will need!
- Spare Parts
- Xray
- M18 / NT18 On-Road
- XRay Adj. Turnbuckle Set For Toe-in Adjustment
Complete set of adjustable turnbuckles for adjusting front and rear toe on M18. A “must have” for serious racers who need to precisely adjust front or rear toe. Set includes threaded rods, balljoints, and pivotballs.
- XRay Alu Drive Shaft with Hex Adapter - Set (2)
CNC-machined drive shafts with hex adaptors are made from tough, high-grade T6 aluminum and high-strength steel pins and fasteners. Ultra-smooth operation, high-precision design and fit. Provides extra strength for use with high-performance motors. This set of two drive shafts comes completely assembled, ready to install. A "must have" for serious drivers involved in high-competition racing. For use with hex-hub micro wheels only.
- XRay Clutch Bell 21T With Bearings
21-tooth clutch bell for NT18 made from HUDY steel. Precision machined on a special gear machine. Includes two 4x7x2.5 bearings.
- XRay Clutch Bell 25T With Bearings
25-tooth clutch bell for NT18 made from HUDY steel. Precision machined on a special gear machine. Includes two 4x7x2.5 bearings.
- XRay Composite Drive Shaft with Hex Adapter - Set (2)
Molded composite drive shafts with hex adaptors. Comes unassembled. Set of 2.
- XRay Front Foam Tire Mounted (2) - Hard
Pre-mounted hard-compound front foam tires on tough composite white 6-spoke rims. Set of 2. Fits NT18 and M18.
- XRay Front Foam Tire Mounted (2) - Medium
Pre-mounted medium-compound front foam tires on tough composite white 6-spoke rims. Set of 2. Fits NT18 and M18.
- XRay Front One-way Differential - Set - Blue
Front one-way differential for M18 allows you to fine-tune the handling characteristics of this already great-handling micro racecar. Allows for quicker steering but decreases braking performance, since only the rear wheels will brake. The one-way differential features high-quality one-way bearings, CNC machined diff body (blue), and high-strength lightweight CNC-machined outdrives made from HUDY Spring Steel™ (available separately)
For use only at the front of the M18, not the rear.
- XRay Fuel Tank 30cc
Factory preassembled 30cc fuel tank set. The fuel tank includes an integrated stone filter. Fits NT18 and NT18T.
- XRay Micro Wheels, F+R (4)
Set of four micro wheels, front and rear.
- XRay Rear Foam Tire Mounted (2) - Medium
Pre-mounted medium-compound rear foam tires on tough composite white 6-spoke rims. Set of 2. Fits NT18 and M18.
- XRay Rear Foam Tire Mounted (2) - Soft
Pre-mounted soft-compound rear foam tires on tough composite white 6-spoke rims. Set of 2. Fits NT18 and M18.
- XRay Rear Foam Tire Mounted with Hex Hub (35Deg) - Soft
Mounted rear foam tires (35deg - soft) on solid dish rims for use with drive shafts with hex adaptors ONLY. Will not fit on original M18 with original wheel mounting system. Set of 2.
- XRay Rubber Tires + Inserts, F+R (40Deg)
Set of four 40deg rubber micro tires and inserts, front and rear.
- XRay Spur Gear 42T / 48
Optional 42 tooth spur gear for M18. This spur should be used for high competition racing to gain better acceleration and improved performance.
NOTE: The optional 42teeth spur gear was designed for the graphite chassis. When using this spur gear on the stock composite chassis, please check the "download area".
- NT1
- XRay Alu Wheel Hub - 2
CNC-machined, premium aircraft aluminum standard offset wheel hubs for XRAY NT1, a direct replacement for composite wheel hubs. These wheel hubs are strategically machined for optimum strength, balance, and lightness, and are marked for easy identification. Secured on drive axle by setscrew. Set of 2 hubs in each package.
• Alu wheel hubs for NT1
• Standard size and 2 offset sizes
• Precision CNC-machined
• Premium aircraft aluminum
• Precision narrowing or widening of track-width
- XRay Anti-Roll Bar Rear 2.2mm
Tough steel rear anti-roll bar wire 2.2mm for precision tuning of the stock rear anti-roll bar. Wide range of bar thicknesses provides great tuning selection.
• Replacement rear anti-roll bar wire
• Tough steel wire
• Tunability choices for standard rear anti-roll bar
- XRay Anti-Roll Bar Rear 2.4mm
Tough steel rear anti-roll bar wire 2.4mm for precision tuning of the stock rear anti-roll bar. Wide range of bar thicknesses provides great tuning selection.
• Replacement rear anti-roll bar wire
• Tough steel wire
• Tunability choices for standard rear anti-roll bar
- XRay Anti-Roll Bar Rear 2.6mm
Tough steel rear anti-roll bar wire 2.6mm for precision tuning of the stock rear anti-roll bar. Wide range of bar thicknesses provides great tuning selection.
• Replacement rear anti-roll bar wire
• Tough steel wire
• Tunability choices for standard rear anti-roll bar
- XRay Brake Pad Ferodo® - 2pcs
Ferodo® fiber brake pads for NT1, must be glued onto #334120 steel brake pads. Set of 2.
- XRay Carrier for 2-Speed Gear (2nd) - Alu 7075 T6 + Ball-Bearing
CNC-machined 2nd gear carrier (drum) made from tough 7075 T6 alu. Includes factory-pressed (non-replaceable) ball-bearing; the ball-bearing must be regularly serviced, cleaned, and oiled.
- XRay Clutch Bell - Hudy Steel
Ultra-strong CNC-machined XCA clutchbell made from special HUDY Steel. Universal design allows quick & easy changing of threaded pinion gears.
- XRay Clutch Shoe - White (Soft)
CNC-machined white clutch shoe for XCA clutch. Material in this clutch shoe is softer and gives higher initial bite but also more slippage and wear.
- XRay Clutch Shoe - Yellow
CNC-machined yellow clutch shoe for XCA clutch. Material in this clutch shoe is harder and gives less slippage and wear.
• Yellow clutch shoe for XCA clutch
• Harder material
• Less slippage
• Improved wear rate
Must have for serious racers.
- XRay Composite 2-Speed Gear 53T (2nd)
XRAY precision molded 53T spur gear (2nd gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 54T (2nd)
XRAY precision molded 54T spur gear (2nd gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 55T (2nd)
XRAY precision molded 55T spur gear (2nd gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 57T (1st)
XRAY precision molded 57 spur gear (1st gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 58T (1st)
XRAY precision molded 58 spur gear (1st gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 59T (1st)
XRAY precision molded 59 spur gear (1st gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear 60T (1st)
XRAY precision molded 60 spur gear (1st gear) made from special composite material which gives the spur gear an optimum balance of hardness, toughness, and flexibility thus providing long life, minimal wear, and minimizing breakage or teeth stripping. The spur gear remain strategically lightened to reduce rotating mass. The special composite material will withstand even the most extreme racing conditions which imparts high tension on the spur gears.
The spur gears are injected in specially constructed mould that ensures equal material injection which ensures ultra true and wobble free running of the spur gear which makes the NT1 spur gears some of the world''s most precise.
Each gear is stamped with a tooth number for easy identification. Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
- XRay Composite 2-Speed Gear Box Shoe Set
2-speed gearbox shoe set. Includes adjusting screws, roller pins, and hardware.
- XRay Composite Ball Cup 8.4mm (8)
Molded composite ball cups for cushioning alu M10 alu adjusting nuts against 8.4mm pivot balls. Set of 8.
- XRay Composite Belt Pulley 18T - 2-Speed-Side
Molded composite 18T side belt pulley on main layshaft, drives side belt.
- XRay Composite Belt Pulley 19T - Mid-Center
Molded composite 19T front belt pulley on middle shaft, drives front belt.
- XRay Composite Belt Pulley 20T - 2-Speed-Center
Molded composite 20T belt pulley on main layshaft, drives rear belt.
- XRay Composite Belt Pulley 25T - Mid-Side
Molded composite 25T mid-side belt pulley. Gives 1.04:1 overdrive ratio to front wheels.
- XRay Composite Belt Pulley 26T - Mid-Side
Molded composite 26T mid-side belt pulley. Gives neutral 1:1 overdrive ratio.
- XRay Composite Bumper
Lower bumper made from tough composite material.
- XRay Composite Caster Clips - 2
Molded composite clips to set front caster adjustment, includes 0.5, 1 and 1.5mm. Set of 2.
- XRay Composite Front Holder for Personal Transponder
Smart, stylish and functional, this personal transponder holder is made from tough composite material, providing solid and secure mounting for your personal transponder for racing. Use with #331201 Composite Wide Bumper.
• Personal transponder holder
• Tough composite material
• Smart, solid, secure
• Bolt-on ingenuity
- XRay Composite Lower & Upper Bulkhead Front Left
Molded composite lower and upper front left bulkhead set.
- XRay Composite Lower & Upper Bulkhead Front Right
Molded composite lower and upper front right bulkhead set.
- XRay Composite Lower & Upper Bulkhead Rear Left
Molded composite lower and upper rear left bulkhead set.
- XRay Composite Lower & Upper Bulkhead Rear Right
Molded composite lower and upper rear right bulkhead set.
- XRay Composite Rear Bulkhead Cover
Molded composite rear bulkhead cover.
- XRay Composite Rear Diff. Case & Cover
Molded composite parts for #335050 rear gear differential. Includes case (with pulley) and cover.
- XRay Composite Rear Upper Camber Link Ball Joint 5.8mm - 4
Molded composite 5.8mm ball joints for rear upper camber link. Set of 4.
- XRay Composite Steering Block Left
Molded composite left-side steering block.
- XRay Composite Steering Block Right
Molded composite right-side steering block.
- XRay Composite Suspension Arm Front Lower
Molded composite suspension arm, front lower. Used on either left or right side.
- XRay Composite Suspension Arm Front Upper
Molded composite suspension arm, front upper. Used on either left or right side.
- XRay Composite Suspension Arm Rear Lower
Molded composite suspension arm, rear lower. Used on either left or right side.
- XRay Composite Upper Holder for Bumper
Upper bumper holder made from tough composite material.
- XRay Composite Upright Rear
Molded composite rear upright with 2 roll center positions, used on left or right side.
- XRay Composite Wide Bumper
Impact-absorbing wide lower front bumper for the NT1 is made from high-quality composite material to better absorb energy from crashes.
• Wide composite lower bumper
• High-quality, tough composite material
• Increased crash protection
- XRay CVD Front Drive Shaft Set - Hudy Spring Steel™
This super-efficient and performance-enhancing front CVD (constant velocity drives) set for the NT1 replaces the standard front drive shaft and drive axle. Rebuildable with separately-available spare parts. Used for FRONT only.
- XRay Diff Bevel & Satellite Gears (2+4)
Differential gears for gear differentials are made from pressed steel, heat treated, and machined for ultra-precision and smooth operation. Includes 2 bevel and 4 satellite gears.
- XRay Diff Pin - 2pcs
Polished steel pins for gear differential. Set of 2.
- XRay Drive Flange with One-Way Bearing - Alu 7075 T6
CNC-machined 1st gear drive flange made from tough 7075 T6 alu. Includes factory-pressed (non-replaceable) high-quality German one-way bearing, hand-ground for maximum running precision and strength. The one-way bearing must be serviced, cleaned, and oiled regularly (we recommend using #309580 One-way Lube).
- XRay Foam Bumper
High-density front bumper cut from specially-developed closed-cell foam material. Very light yet very strong. Protects front of car in serious collisions.
- XRay Foam Bumper - Hard
This new front bumper - made from extra-stiff yet lightweight closed-cell foam - will help to protect the car better and will not yield even in heavy collisions. Recommended for all racing conditions but especially for tracks with rigid or sharp perimeter boards.
• Harder, extra-stiff foam front bumper
• Increased crash protection
• Tough, pre-shaped closed-cell foam
• Pre-drilled mounting holes
- XRay Fuel Tank 75cc - Set
Quick-fill low CG 75cc fuel tank set for NT1. Includes tank inserts to limit the fuel capacity, and 3mm lowering shims when using optional micro-size receiver battery pack. Includes an integrated stone filter and splashguard.
- XRay Fuel Tank Mounting Grommet (3)
Soft, tough rubber mounting grommets for mounting NT1 fuel tank. Set of 3.
- XRay Graphite Battery Plate
Optional CNC-machined plate has recessed slots for 5-cell receiver pack. Made from premium-quality woven graphite material. Smart design and strong material increases chassis longitudinal stiffness, complementing the Multi-Flex Technology™ engine mount.
• Graphite battery plate
• Direct replacement for composite battery plate
• Adds stylish graphite accent to NT1
• Increases chassis stiffness
- XRay Graphite Shock Tower Front 2.5mm
CNC-machined front shock tower made from top-grade 2.5mm thick graphite. Includes multiple shock upper mounting positions.
- XRay Graphite Shock Tower Rear 3mm
CNC-machined rear shock tower made from top-grade 3.0mm thick graphite. Includes multiple shock upper mounting positions.
- XRay Graphite Upper Holder for Bumper
Tough, strong and light front upper bumper holder for NT1 made from thick, highest-quality CNC-machined top-grade graphite. A direct replacement for the stock composite upper bumper.
• Graphite upper bumper holder
• Precision CNC-machined
• Thick premium graphic material
• Extra rigid and strong
• Direct replacement for stock composite bumper
- XRay Multi-Diff - One-Way - Solid - Set
Revolutionary, XRAY Multi-Diff™ (XRAY patent) is now offered for the NT1. This versatile front axle system offers three different settings: one-way / one-way solid / full-time solid axle. You can easily use the Multi-Diff™ as a standard one-way (left and right outdrives turn independently off-power), or lock the one-way out drives (both left and right outdrives turn together off-power), or you can fully lock the Multi-Diff™ and it will work as a full-time solid axle.
- XRay Pur Reinforced Drive Belt Front 3x186mm
PUR® reinforced front drive belt. 3 x 186mm. This belt is very thin and elastic as possible for an extremely efficient, low-friction drivetrain.
- XRay Pur Reinforced Drive Belt Rear 3x177mm
PUR® reinforced rear drive belt. 3 x 177mm. This belt is very thin and elastic as possible for an extremely efficient, low-friction drivetrain.
- XRay Pur Reinforced Drive Belt Side 3x390mm
PUR® reinforced side drive belt. 3 x 390mm. This belt is very thin and elastic as possible for an extremely efficient, low-friction drivetrain.
- XRay Rear Gear Differential - Set
Complete rear gear differential set for NT1 includes composite differential case and cover. Differential gears are made from pressed steel, heat treated, and machined for ultra-precision and smooth operation. CNC-machined diff outdrive adaptors made from tough HUDY Spring Steel™. Shafts are precision ground and polished for smooth operation. Not factory pre-assembled.
- XRay Shim 5x7x0.2 (10)
XCA clutch shims. 5x7x0.2mm. Set of 10.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 15T (1st)
High-strength 15T pinion gear (1st gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 16T (1st)
For the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 17T (1st)
High-strength 17T pinion gear (1st gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 18T (1st)
High-strength 18T pinion gear (1st gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 20T (2nd)
High-strength 20T pinion gear (2nd gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 21T (2nd)
High-strength 21T pinion gear (2nd gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 22T (2nd)
High-strength 22T pinion gear (2nd gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- XRay XCA Alu 7075 T6 Hardcoated Pinion Gear - 23T (2nd)
High-strength 23T pinion gear (2nd gear) for the XRAY NT1 are made from tough 7075 T6 alu and specially hardcoated for supreme strength, light weight, and high durability. Created on a special gear machine, all pinions feature ultra-precise tooth shaping and ultra-true running for vibration-free operation. Fine internal threading allows easy installation on XCA clutchbells (standard or lightweight versions). Each pinion is fine etched with the tooth number for easy & quick identification.
- Others
- Hudy Micro Start - Box 1/18th
This is a Hudy micro starter box for 1/18th scale nitro micro cars.
- XRay 4.0mm Flanged Nuts (10)
- XRay 4.0mm Nuts (10)
- XRay Ball Bearing 4x7x2.5 MR74ZZ (2)
This is set of two replacement 4x7x2.5mm bearings for the XRAY M18 1/18th scale touring car.
- XRay Ball Bearing 6700ZZ, 10mm x 15mm x 4mm, High Speed (2)
Ball Bearing 6700ZZ, 10mm x 15mm x 4mm, High Speed (2).
- XRay Carbide Ball 2.4mm For Ball Differential (12)
This is a set of twelve optional carbide differential balls for the XRAY M18 1/18th scale touring car.
- XRay CH-Chlip 8 - 10
8mm dia. CH-clip. Set of 10 pieces.
- XRay Cone Washer ST 3x8x0.5 (10)
Cone washer ID x OD x thickness = 3mm x 8mm x 0.5mm. Set of 10 pieces.
- XRay Foam Stand for T2
Foam work stand for XRAY T2 made from premium, high-density, resilient closed-cell foam. Makes working on your T2 very easy! Includes special holes for shock absorbers.
- XRay GlowPlug
High-quality std. glowplug for NT18 engine. Includes copper gasket.
- XRay Hex Screw SH 3x16mm (10)
This is a pack of ten replacement 3x16mm set screws for the XRAY NT18 1/18th scale touring car.
- XRay Hex Screw SH 3x18mm (10)
This is a pack of ten replacement 3x18mm set screws for the XRAY NT18 1/18th scale touring car.
- XRay Hex Screw SH M2x5 (10)
M2x5 button-head machine screw, hex drive. Set of 10 pieces.
- XRay Hex Screw SH M3x4 - Stainless (10)
M3x4 button-head stainless steel machine screw, hex drive. Set of 10 pieces.
- XRay Hex Screws SB 3 x 2.5mm (10) Set Screws
Hex Screws SB 3 x 2.5mm (10) Set Screws.
- XRay High Speed Ball Bearing 5x10x4 (Rubber Sealed)
This is set of two replacement 5x10x4mm bearings for the XRAY T2 1/10th scale touring car.
- XRay Lanyard
Stylish and strong high-quality fabric lanyard with XRAY logos printed in white.
- XRay Muffler Rubber Connector
This is a replacement muffler rubber connector for the XRAY NT18 1/18th scale touring car.
- XRay One-Way Lube 25ML
Special lubricant for one-way bearings used on XRAY T1 in one-way differential or on the main layshaft.
- XRay O-Ring 10 x 1.5 (10)
Rubber O-ring 1.5mm thick x 10mm dia. Set of 10 pieces.
- XRay O-Ring 12.1x1.6 (10)
Rubber O-ring fits over 12mm shaft. 1.6mm thick. Set of 10 pieces.
- XRay O-Ring 5x1 (10)
Rubber O-ring fits over 5mm shaft. 1mm thick. Set of 10 pieces.
- XRay Pin 2x10 (10)
This is a set of ten replacement 2x10mm pins for the XRAY T2 1/10th scale touring car. These pins are used in the universals. Replaces #309452.
- XRay Pin 2x8 (10)
Polished chrome pin. Dia. x length = 2mm x 12mm. Set of 10 pieces.
- XRay Premium Silicone Oil (100 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (1000 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (150 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (20 000 CST)
Premium Silicone Oil (20 000 CST).
- XRay Premium Silicone Oil (200 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (2000 CST)
Premium Silicone Oil (2000 CST)
- XRay Premium Silicone Oil (250 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (300 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (3000 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (400 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (450 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (500 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (600 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil (7000 CST)
XRAY Premium Silicone Oil is manufactured in Europe by a specialized silicone oil premium manufacturer.
- XRay Premium Silicone Oil 350 cSt
XRAY Premium Silicone Oil 350 cSt is manufactured in Europe by a specialized silicone oil premium manufacturer, these new oils were exclusively created for XRAY. Each batch of premium oil is laboratory tested and calibrated to ensure the highest possible consistency and quality from batch to batch. Based on the industry-proven CST rating, the new line of oils will be easy to identify, adjust, and feel.
- XRay Silcone Grease
- XRay Silicone O-Ring 3.1x1.6 (10)
Silicone O-ring fits over 3mm shaft. 1.6mm thick. Set of 10 pieces.
- XRay Washer S 3.5x12x0.2 (10)
- XRay XMS01MG Micro Servo – Metal Gear
The XRAY XMS01MG micro servo with metal gears has been specially chosen for the M18 micro racecar because of its high precision, long life and high quality.
- T2'007 EU Rubber Spec
- T2 007 Upper Deck Graphite - Narrow 2.0mm - Set
- XRay Additional XRAY Ultimate Racing Springs (20)
For even more fine tuning of suspension dampening, XRAY offers an additional set of ultra-fine tuning springs in addition to the basic set (#308390) of XRAY springs. The ultra-fine tuning springs have different damping and compression characteristics that fall between the range of the springs in the basic set.
- XRay Alu Ball Diff. With Labyrinth Covers
Complete ball-differential set features hardcoated duraluminum output shafts, screw for external adjustment, both diff pulleys (2.125 and 1.77) with Labyrinth Dust Covers™, high-performance ball-bearings, carbide axial thrustbearing, heavy-duty diff washers, and carbide diff balls.
- XRay Alu Middle One-Way Pulley Set
- XRay Alu Shim 3x5x1.0 (10)
Alu shims, 1.0mm thick, for rear roll center adjustment on XRAY T2. Set of 10.
- XRay Alu Shim for Lower Susp. Holder 3x7.5x1.5 (10)
Steel shims, 1.5mm thick, for track-width and rear toe adjustment on XRAY T2. Set of 10.
- XRay Alu Wheel Shim Offset 0.75mm (2)
Alu wheel shim with 0.75mm offset. Set of 2. Fits T2.
- XRay Balancing Chassis Weights (Center - 3 pcs)
A complete set of 3 chassis balancing weights and mounting hardware.
- XRay Delrin Solid Axle Body - Lightweight
For serious racers looking for an edge, XRAY''s new ultra-true, high-durability solid front axle body is CNC machined from lightweight Delrin® composite material, making it 25% lighter than the original Multi-Diff. This solid axle transforms the XRAY Multi-Diff into a full-time solid axle only; remaining parts must be used from the Multi-Diff. Fits all XRAY touring cars.
Used by XRAY Factory Team - a "must have" for serious racers.
- XRay Diff Pulley 34T With Labyrinth Dust Covers
Precise nylon pulley (34T) and Labyrinth Dust Covers for ball-differential.
- XRay Diff Washer 17x23x1 (2)
Two diff washers for ball-differentials. Each side of the washer has a distinct finish; a polished side against which the diff balls ride, and a rougher machined side that contacts the duraluminum diff output. Specially hardened to assure maximum life.
- XRay Drive Shaft Replacement Plastic Cap 3mm (4) - V2
Low friction drive pin clips for protection and cushioning of drive shaft pin in diff outdrives. Set of four.
V2 Update: Both the material and design have been improved to reduce wear of the differential outdrives. The improved design makes the installation the clips a bit more complicated.
- XRay Fixed Pulley 20T (2)
Precision-molded 20T layshaft pulleys for XRAY T1FK’05. Set of two.
- XRay Graphite Motor Guard
- XRay High-Performance Kevlar Drive Belt Front 3x507mm
Ultra-Flex High-Performance Drive Belt
For top competition racing XRAY offers these specially modified high-performance Kevlar reinforced drive belts. The belts are very thin and elastic as possible to create much more effective transmissions, save batteries and eliminate friction. The belt is specially modified - hand ground on a special machine so the belt is as thin as possible, but in such a way that it will still have long life.
"A must have item for serious racers."
- XRay High-Performance Kevlar Drive Belt Rear 3x180mm
Specially modified high-performance Kevlar-reinforced 3mm-wide drive belt is 1mm narrower than original 4mm belt (#305441) for increased transmission efficiency. This belt is very thin and elastic as possible for an extremely effective transmission that saves batteries and eliminates friction. The belt is specially modified - hand ground on a special machine so the belt is as thin as possible, but in such a way that it will still have long life.
- XRay Nylon Pistons Adjustable + Non-Adjust. (Set 2+6)
New nylon piston set to work with new keyed piston rods (308152 and 308252).
The complete keyed shock piston conversion set offers a professional solution for the adjustable XRAY & Serpent shocks.
The single frame includes the following parts:
- 2 new adjustable pistons
- 2 sets of 3 different non-adjustable pistons (with 2,3,4 holes).
NOTE: These pistons are not interchangable with those in Serpent 909401 Shock-parts Nylon F+R set.
- XRay Precision Balancing Chassis Weights (Front) (2)
This is a set of two optional chassis balancing weights for the XRAY T2 1/10th scale touring car.
- XRay Precision Balancing Chassis Weights (Rear) (6)
This is a set of six optional chassis balancing weights for the XRAY T2 1/10th scale touring car.
- XRay Shock Foam Inserts (4)
Foam inserts for XRAY shocks, go between shock upper mount and rubber membrane. Set of 4 pieces.
- XRay Shockabsorber Membranes (4)
Silicon-rubber compensation membranes for shock absorbers. Set of four.
- XRay Spring-Set D=1.4 (14 LB) Yellow - Super Soft (4)
Set of four coil-springs for XRAY shock absorbers. All 4 springs within the set have the same length and damping characteristics.
Colour: Yellow
Tension: Very Soft
NOT interchangeable with yellow springs for Serpent shocks - 308096 Spring-set D=1.6 Yellow (2+2)
- XRay Spring-Set D=1.5 (15 LB) Blue-Green (4)
For even more fine tuning of suspension dampening, XRAY offers an additional ultra-fine tuning springs in addition to the basic XRAY springs. The ultra-fine tuning springs have different damping and compression characteristics that fall between the range of the basic springs. All 4 springs within the set have the same length and damping characteristics.
- XRay Spring-Set D=1.5 (17.5 LB) White - Soft (4)
Set of four coil-springs for XRAY shock absorbers. All 4 springs within the set have the same length and damping characteristics.
Colour: White
Tension: Soft
NOT interchangeable with yellow springs for Serpent shocks - 308095 Spring-set D=1.5 White (2+2)
- XRay Spring-Set D=1.6 (20 LB) Light-Blue (4)
For even more fine tuning of suspension dampening, XRAY offers an additional ultra-fine tuning springs in addition to the basic XRAY springs. The ultra-fine tuning springs have different damping and compression characteristics that fall between the range of the basic springs. All 4 springs within the set have the same length and damping characteristics.
- XRay Spring-Set D=1.6 (22.5 LB) Blue - Soft-Medium (4)
Set of four coil-springs for XRAY shock absorbers. All 4 springs within the set have the same length and damping characteristics.
Colour: Blue
Tension: Soft-Medium
- XRay Spur Gear 112T/64
XRAY precision molded spur gear 112 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass.
- XRay Spur Gear 114T/64
XRAY precision molded spur gear 114 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass.
- XRay Spur Gear 116T/64
XRAY precision molded spur gear 116 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass.
- XRay Spur Gear 118T/64
XRAY precision molded spur gear 118 tooth, 64 pitch. This spur gear has been strategically lightened to reduce rotating mass.
- XRay Steel Shim for Lower Susp. Holder 3x7.5x0.4 (10)
Steel shims, 0.4mm thick, for track-width and rear toe adjustment on XRAY T2. Set of 10.
- XRay Steel Shim For Lower Suspension Holder 3x7.5x0.75 (10)
Steel shims, 0.75mm thick, for track-width and rear toe adjustment on XRAY T2. Set of 10.
- XRay T2 +0.75mm Aluminum Wheel Hub Set (2)
- XRay T2 Alu Shim 3x6x1.0mm (10)
Alu shims, 1mm thick, for wheelbase adjustment on XRAY T2. Set of 10.
- XRay T2 Alu Shim 3x6x2.0mm (10)
Alu shims, 2mm thick, for wheelbase adjustment on XRAY T2. Set of 10.
- XRay T2 Alu Shim 3x6x2.0mm (10)
Alu shims, 2mm thick, for wheelbase adjustment on XRAY T2. Set of 10.
- XRay T2 Alu Wheel Hub (2)
CNC-machined clamping-style alu wheel hubs for XRAY T2. Set of two.
- XRay T2 Anti-Roll Bar Front (Set)
If your XRAY T2 is oversteering, then try this optional front anti-roll bar set. The front anti-roll bar will decrease front chassis roll and decrease front traction, reducing your car’s steering. This complete front anti-roll bar set for the XRAY T2 includes all necessary hardware, and includes three different anti-roll bars: 1.2, 1.4, and 1.6mm.
- Xray T2 Anti-Roll Bar Rear (Set)
If your XRAY T2 is understeering, then try this optional rear anti-roll bar set. The rear anti-roll bar will decrease rear chassis roll and decrease rear traction, increasing your car’s steering. This complete rear anti-roll bar set for the XRAY T2 includes all necessary hardware, and includes three different anti-roll bars: 1.2, 1.4, and 1.6mm.
- XRay T2 Ball Joint 5mm - Open (8)
Molded composite 5mm ball joints, open on both sides, for connection to 5mm ball. Set of eight. Fits XRAY T2.
- XRay T2 Ball Joint 5mm Unidirectional - Open (4)
Molded composite 5mm ball joints, special construction. For connection to 5mm ball. Set of four. Fits XRAY T2.
- XRay T2 Ball-Bearing Composite Bushing (4)
Molded composite bushings for installing ball-bearings in T2 alu steering blocks (302256) and alu rear uprights (303358 and 303359). Set of 4.
- XRay T2 Composite Bumper
Lower bumper holder made from tough composite material. Fits XRAY T2.
- XRay T2 Composite C-Hub Bushing (2+2)
Composite bushings for all T2 alu C-hubs.
- XRay T2 Composite C-Hub Front Block, Left - 2° Deg.
Molded C-hub for left steering block of T2. Caster pre-set at 2°. Engraved with "L2" to easy identification. Use with right-side composite 2° C-hub #302343.
- XRay T2 Composite C-Hub Front Block, Left - 4° Deg.
Molded composite C-hub for front left steering block on XRAY T2. Caster pre-set at 4° for neutral handling. Engraved with "4L" for easy identification. Use with left-side composite 4° C-hub #302345.
- XRay T2 Composite C-Hub Front Block, Left - 6° Deg.
Molded C-hub for left steering block of T2. Caster pre-set at 6°. Engraved with "L6" to easy identification. Use with right-side composite 6° C-hub #302347.
- XRay T2 Composite C-Hub Front Block, Right - 2° Deg.
Molded C-hub for right steering block of T2. Caster pre-set at 2°. Engraved with "R2" to easy identification. Use with left-side composite 2° C-hub #302344.
- XRay T2 Composite C-Hub Front Block, Right - 4° Deg.
Molded composite C-hub for front right steering block on XRAY T2. Caster pre-set at 4° for neutral handling. Engraved with "4R" for easy identification. Use with left-side composite 4° C-hub #302346.
- XRay T2 Composite C-Hub Front Block, Right - 6° Deg.
Molded C-hub for right steering block of T2. Caster pre-set at 6°. Engraved with "R6" to easy identification. Use with left-side composite 6° C-hub #302348.
- XRay T2 Composite Upper Holder for Bumper
Upper bumper holder made from tough composite material. Fits XRAY T2.
- XRay T2 Composite Upright 1° Outboard Toe-In - Left
Molded composite upright for use on rear left of XRAY T2. Outboard toe pre-set at 1° ; engraved with "1L" for easy identification. Use with left-side composite 1° rear upright #303351.
- XRay T2 Composite Upright 1° Outboard Toe-In - Right
Molded composite upright for use on rear right of XRAY T2. Outboard toe pre-set at 1° ; engraved with "1R" for easy identification. Use with left-side composite 1° rear upright #303361.
- XRay T2 Foam Bumper
High-resilience lightweight foam front bumper. Fits XRAY T2.
- XRay T2 Front Body Mount Set 6mm
Front body mount set includes redesigned 6mm-thick bodyposts and all other mounting hardware. Fits XRAY T2.
- XRay T2 Front Suspension Pivot Pin (2)
Front lower inner pivot pins for XRAY T2. Hardened for very high durability and long life. Set of two.
- XRay T2 Graphite Battery Stand X/Alu Stands - 1 Set
- XRay T2 Lower Suspension Holders (2+2+2)
Molded composite lower suspension pin holders for use in XRAY T2.
- XRay T2 Pivot Ball 5.0mm Double Bevel Shoulders (10)
Specially-machined 5.0mm pivot ball with double bevel shoulders, for use with open 5.0mm ball joints on XRAY T2. Set of 10.
- XRay T2 Rear Body Mount Set 6mm
Rear body mount set includes redesigned 6mm-thick bodyposts and all other mounting hardware. Fits XRAY T2.
- XRay T2 Rear Suspension Arm - Hard - Rubber-Spec
Hard molded composite rear lower suspension arm. Recommended for use in standard conditions or with rubber tires. Marked with “H” for easy identification. May be used on either left or right side.
- XRay T2 Rear Suspension Pivot Pin (2)
Rear lower inner pivot pins for XRAY T2. Hardened for very high durability and long life. Set of two.
- XRay T2 Shock Ball Joint – Open (4)
Molded composite ball joints for ends of XRAY T2 shock shafts. Set of four.
- XRay T2 Steel Steering Brushing (2+2)
Precision-machined bushing for front C-hub steering block pivot screws on XRAY T2. Includes 4 pieces: 2 short + 2 long.
- XRay T2 Upper Holder for Bumper - 2.5mm Graphite
CNC-machined front upper bumper holder for T2 made from highest-quality 2.5mm woven graphite.
- XRay Timing Belt Pulley 34T
High-quality, lightened molded 34 teeth pulley with special "side click-covers" for front one-way differential.
- XB8 EC
- XRay Air Filter Foam & Oil
Inner and outer foam filter elements, and a tube of air filter oil.
- XRay Air Filter Set
Complete air filter set for XB8. Includes composite filter elbow, base and cap, and inner/outer foam elements. Also includes tie-wraps and air filter oil.
- XRay Alu Clutch Shoes - Light 1.71g - CNC Machined (3)
These new 1.71g clutch shoes are slightly lighter than the stock aluminum shoes, allowing the engine to spool up a bit more before the shoes grab the flywheel. The end result is a clutch that will engage later in the powerband giving more rip out of the corners.
- XRay Ball-Bearing Set - Rubber Covered For XB8 (24)
Complete set of rubber-covered ball bearings for XB8. Set of 24.
- XRay Bevel Drive Gear 12T
12-tooth bevel drive gear for front/rear differential. Precision machined on a special gear machine.
- XRay Brake Pad Ferodo (4)
Ferodo fiber brake pads. Set of 4.
- XRay Caster Clips (2)
Molded clips for adjusting position of front upper arm. Includes 1mm, 2mm, and 3mm thick clips. Set of 2.
- XRay C-Hub Left
Left-side C-hub block made from tough molded composite. Features multiple mounting positions for front upper arm. The C-hub features Xray smart I.A.C. (Integrated Adjustable Caster) that enables one C-hub block complete caster range adjustment. Xray patent.
- XRay C-Hub Right
- XRay Clutch Bell 13T
13-tooth clutch bell made from HUDY steel. Precision machined on a special gear machine.
- XRay Clutch Bell Ball-Bearing MR105ZZ 5x10x4 (2)
High-performance clutch bell ball-bearings 5x10x4. Packed with grease specially made for clutch bell. Qty of 2.
- XRay Clutch Springs 1.1mm (3)
Steel clutch springs. Wire diameter 1.1mm (hard) for later clutch engagement. Set of 3.
- XRay Clutch Springs 1mm (3)
Steel clutch springs. Wire diameter 1.0mm (hard) for later clutch engagement. Set of 3.
- XRay Composite Fuel Filter Set
Fuel filter set made from tough composite material and the aluminum cap is machined from premium aluminum. A sieve is installed in the fuel filter. The body of the fuel filter has a slot that enables the filter to sit in the holder perfectly and prevents the filter from turning.
- XRay Diff Gasket (4)
Sealing gasket for differential housing. Set of 4.
- XRay Diff Pin (2)
Precision-ground polished steel pins for differential internal satellite gears. Set of 2.
- XRay Differential Case
Rubber sealed composite differential housings made from tough composite are manually precision ground after the molding process to guarantee a perfect fit with no vibration. Used for front/rear and center differentials.
- XRay Front & Rear Bumper
Tough composite bumpers for XB8. Set of two (front / rear).
- XRay Front Anti-Roll Bar 2.2mm
Front anti-roll bar, 2.2mm thick.
- XRay Front Anti-Roll Bar 2.6mm
Front anti-roll bar, 2.6mm thick.
- XRay Front Anti-Roll Bar 2.8mm
Front anti-roll bar, 2.8mm thick.
- XRay Front Anti-Roll Bar 3.0mm
Front anti-roll bar, 3.0mm thick.
- XRay Front Anti-Roll Bar 3.2mm
Front anti-roll bar, 3.2mm thick.
- XRay Front Diff Large Bevel Gear 38T
The new 38T front diff crown gear for the XB8 is CNC-machined from hardened HUDY steel developed specially for gears, allowing for ultra-true, vibration-free running. All edges are chamfered for smooth engagement. The "38" symbol is laser-engraved for easy recognition, as well as the bearing size is ground for maximum precision. Using this gear in the front diff of your XB8 alters the gear ratio from 3.333 (with 40T original gear) to 3.167. This makes the car easier to drive, especially in bumpy condition, and improves on-power stability. The new 38T front diff crown gear improves traction and reduces sliding.
- XRay Front TQ Lower Suspension Arm
The redesigned front lower suspension arms with all new special profile provide higher stiffness and rigidity to prevent bending of the arm under extreme racing conditions. The arms are moulded from a special composite mixture that provides sufficient flexibility to give easy-driving handling characteristics in all racing conditions. The arms are also longer, providing more stability and the updated design also allows more downtravel than the previous versions.
- XRay Front Upper Arm
Front upper suspension inner arm made from tough molded composite. May be used on either left or right side.
- XRay Front/Rear Diff Large Bevel Gear 40T
- XRay Fuel Tank 120cc - Set
Factory preassembled 120cc fuel tank set. The fuel tank includes an integrated stone filter and splashguard to protect the brakes from fuel.
- XRay Fuel Tank Mounting Grommet (4)
Soft rubber mounting grommets for fuel tank absorb vibrations. Set of 4.
- XRay Rear Anti-Roll Bar 2.4mm
Rear anti-roll bar 2.4mm thick.
- XRay Rear Anti-Roll Bar 2.6mm
Rear anti-roll bar 2.6mm thick.
- XRay Rear Anti-Roll Bar 3.0mm
Rear anti-roll bar 3.0mm thick.
- XRay Rear Anti-Roll Bar 3.2mm
Rear anti-roll bar 3.2mm thick.
- XRay Rear TQ Lower Suspension Arm Left
The redesigned rear lower suspension arm (left) with all new special profile provides higher stiffness and rigidity to prevent bending of the arm under extreme racing conditions. The arms are moulded from a special composite mixture that provides sufficient flexibility to give easy-driving handling characteristics in all racing conditions. The arms are also longer, providing more stability and the updated design also allows more downtravel than the previous versions.
- XRay Rear TQ Lower Suspension Arm Right
The redesigned rear lower suspension arm (right) with all new special profile provides higher stiffness and rigidity to prevent bending of the arm under extreme racing conditions. The arms are moulded from a special composite mixture that provides sufficient flexibility to give easy-driving handling characteristics in all racing conditions. The arms are also longer, providing more stability and the updated design also allows more downtravel than the previous versions.
- XRay Rear Wing
Aerodynamic rear wing molded from a very flexible composite mixture. All edges in critical areas are reinforced to prevent breakage.
- XRay Rear Wing - Orange
Aerodynamic rear wing (orange) molded from a very flexible composite mixture. All edges in critical areas are reinforced to prevent breakage.
- XRay Rear Wing (Black)
Aerodynamic rear wing (black) molded from a very flexible composite mixture. All edges in critical areas are reinforced to prevent breakage.
- XRay Rear Wing Posts
Rear wing posts made of tough composite. Complete set of 4 pieces.
- XRay Shock Boot - 4pcs
Soft rubber shock boots keep dirt and debris off the shock rod and out of the shock body. Set of 4.
- XRay Shock Rubber Membrane - 4pcs
Shock rubber membrane made of soft molded rubber. Set of 4.
- XRay Spring-Set Hard Dark-Blue (2+2)
XRAY suspension spring set for XB8. Hard spring tension. Powder-coated dark blue colour for easy identification. Complete set of 2 front and 2 rear springs.
- XRay Steel Brake Pad – Laser Cut - Hardened (4)
High-precision, ultra-efficient steel brake pads are one of the best in the market! The steel brake pads are laser cut and afterwards precisely ground on both sides for an ultra-smooth surface finish that guarantees maximum braking efficiency. This set of exclusive brake pads is additionally hardened to increase the life and provide higher stiffness. A must have for serious racers. Set of 4.
- XRay Steel Diff Bevel & Satellite Gears (2+4)
Pressed steel differential bevel and satellite gears. Heat-treated and machined for ultra-precision and smooth operation. Set includes 2 bevel gears and 4 satellite gears.
- XRay Steering Plate Bushing (2)
High-strength steering plate bushing. Qty of 2.
|
